ICode9
精准搜索请尝试： 精确搜索
首页
编程语言>
数据库
系统相关
互联网
其他分享
Python
Java
JavaScript
android
PHP
首页 > 其他分享> 文章详细

104-CH32V307(WCH单片机)学习开发-串口

2022-05-19 17:31:07  阅读：205  来源： 互联网

标签：USART CH32V307 NVIC 单片机 InitStructure Mode 串口 GPIO


<p><iframe name="ifd" src="https://mnifdv.cn/resource/cnblogs/LearnCH32V307VCT6" frameborder="0" scrolling="auto" width="100%" height="1500"></iframe></p>

<iframe frameborder="0" height="1500" name="ifd" scrolling="auto" src="https://mnifdv.cn/resource/cnblogs/LearnCH32V307VCT6" width="100%"></iframe>

 

串口1

void uart_init(u32 bound1){
    GPIO_InitTypeDef GPIO_InitStructure;
    USART_InitTypeDef USART_InitStructure;
    NVIC_InitTypeDef NVIC_InitStructure;

    RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA|RCC_APB2Periph_GPIOB|RCC_APB2Periph_USART1|RCC_APB2Periph_AFIO , ENABLE);

    //USART1_TX   GPIOA.9
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
    GPIO_Init(GPIOA, &GPIO_InitStructure);
    //USART1_RX   GPIOA.10初始化
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU;
    GPIO_Init(GPIOA, &GPIO_InitStructure);

    //USART 初始化设置
    USART_InitStructure.USART_WordLength = USART_WordLength_8b;//字长为8位数据格式
    USART_InitStructure.USART_StopBits = USART_StopBits_1;//一个停止位
    USART_InitStructure.USART_Parity = USART_Parity_No;//无奇偶校验位
    USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;//无硬件数据流控制
    USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx; //收发模式

    USART_InitStructure.USART_BaudRate = bound1;//串口波特率
    USART_Init(USART1, &USART_InitStructure); //初始化串口1

    /*中断优先级配置*/
    NVIC_InitStructure.NVIC_IRQChannel = USART1_IRQn;
    NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority=3;
    NVIC_InitStructure.NVIC_IRQChannelSubPriority = 3;
    NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
    NVIC_Init(&NVIC_InitStructure); //根据指定的参数初始化VIC寄存器

    USART_ITConfig(USART1, USART_IT_RXNE, ENABLE);//开启串口接受中断

    USART_Cmd(USART1, ENABLE);                    //使能串口
}



//串口中断服务程序
__attribute__((interrupt("WCH-Interrupt-fast")))
void USART1_IRQHandler(void)
{
    u8 Res;
    if(USART_GetITStatus(USART1, USART_IT_RXNE) != RESET)
    {
        Res =USART_ReceiveData(USART1); //读取接收到的数据
    }
}

 

串口发送数据

void usart_send_bytes(USART_TypeDef *USARTx, char *c,uint32_t cnt)
{
    while(cnt--)
    {
        USART_SendData(USARTx, *c++);
        while(USART_GetFlagStatus(USARTx, USART_FLAG_TXE) == RESET );
    }
}


usart_send_bytes(USART1, "11223344", 4);//发送数据

 

 

串口1,2,3

void uart_init(u32 bound1,u32 bound2,u32 bound3){
    GPIO_InitTypeDef GPIO_InitStructure;
    USART_InitTypeDef USART_InitStructure;
    NVIC_InitTypeDef NVIC_InitStructure;

    RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART2|RCC_APB1Periph_USART3, ENABLE);
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA|RCC_APB2Periph_GPIOB|RCC_APB2Periph_USART1|RCC_APB2Periph_AFIO , ENABLE);

    //串口引脚
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
    GPIO_Init(GPIOA, &GPIO_InitStructure);

    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU;
    GPIO_Init(GPIOA, &GPIO_InitStructure);

    //串口引脚
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_2;
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
    GPIO_Init(GPIOA, &GPIO_InitStructure);

    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_3;
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU;
    GPIO_Init(GPIOA, &GPIO_InitStructure);

    //串口引脚
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
    GPIO_Init(GPIOB, &GPIO_InitStructure);

    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_11;
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU;
    GPIO_Init(GPIOB, &GPIO_InitStructure);

    //USART 初始化设置
    USART_InitStructure.USART_WordLength = USART_WordLength_8b;//字长为8位数据格式
    USART_InitStructure.USART_StopBits = USART_StopBits_1;//一个停止位
    USART_InitStructure.USART_Parity = USART_Parity_No;//无奇偶校验位
    USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;//无硬件数据流控制
    USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx; //收发模式

    USART_InitStructure.USART_BaudRate = bound1;//串口波特率
    USART_Init(USART1, &USART_InitStructure); //初始化串口1

    USART_InitStructure.USART_BaudRate = bound2;//串口波特率
    USART_Init(USART2, &USART_InitStructure); //初始化串口2

    USART_InitStructure.USART_BaudRate = bound3;//串口波特率
    USART_Init(USART3, &USART_InitStructure); //初始化串口3

    /*串口--1*/
    NVIC_InitStructure.NVIC_IRQChannel = USART1_IRQn;
    NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority=3;
    NVIC_InitStructure.NVIC_IRQChannelSubPriority = 3;
    NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
    NVIC_Init(&NVIC_InitStructure); //根据指定的参数初始化VIC寄存器

    /*串口--2*/
    NVIC_InitStructure.NVIC_IRQChannel = USART2_IRQn;
    NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority=0;
    NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
    NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
    NVIC_Init(&NVIC_InitStructure); //根据指定的参数初始化VIC寄存器

    /*串口--3*/
    NVIC_InitStructure.NVIC_IRQChannel = USART3_IRQn;
    NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority=1;
    NVIC_InitStructure.NVIC_IRQChannelSubPriority = 1;
    NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
    NVIC_Init(&NVIC_InitStructure);

    USART_ITConfig(USART1, USART_IT_RXNE, ENABLE);//开启串口接受中断
    USART_ITConfig(USART2, USART_IT_RXNE, ENABLE);//开启串口接受中断
    USART_ITConfig(USART3, USART_IT_RXNE, ENABLE);//开启串口接受中断

    USART_Cmd(USART1, ENABLE);                    //使能串口
    USART_Cmd(USART2, ENABLE);                    //使能串口
    USART_Cmd(USART3, ENABLE);                    //使能串口
}


//串口中断服务程序
__attribute__((interrupt("WCH-Interrupt-fast")))
void USART1_IRQHandler(void)
{
    u8 Res;
    if(USART_GetITStatus(USART1, USART_IT_RXNE) != RESET)
    {
        Res =USART_ReceiveData(USART1); //读取接收到的数据
    }
}

//串口中断服务程序
__attribute__((interrupt("WCH-Interrupt-fast")))
void USART2_IRQHandler(void)
{
    u8 Res;
    if(USART_GetITStatus(USART2, USART_IT_RXNE) != RESET)
    {
        Res =USART_ReceiveData(USART2); //读取接收到的数据
    }
}

//串口中断服务程序
__attribute__((interrupt("WCH-Interrupt-fast")))
void USART3_IRQHandler(void)
{
    u8 Res;
    if(USART_GetITStatus(USART3, USART_IT_RXNE) != RESET)
    {
        Res =USART_ReceiveData(USART3); //读取接收到的数据
    }
}

 

串口4

void uart_init(u32 bound4){
    //GPIO端口设置
    GPIO_InitTypeDef GPIO_InitStructure;
    USART_InitTypeDef USART_InitStructure;
    NVIC_InitTypeDef NVIC_InitStructure;

    RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART2|RCC_APB1Periph_USART3|RCC_APB1Periph_UART4, ENABLE);
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA|RCC_APB2Periph_GPIOB|RCC_APB2Periph_GPIOC|RCC_APB2Periph_USART1|RCC_APB2Periph_AFIO , ENABLE);

    //串口引脚
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
    GPIO_Init(GPIOC, &GPIO_InitStructure);

    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_11;
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU;
    GPIO_Init(GPIOC, &GPIO_InitStructure);


    //USART 初始化设置
    USART_InitStructure.USART_WordLength = USART_WordLength_8b;//字长为8位数据格式
    USART_InitStructure.USART_StopBits = USART_StopBits_1;//一个停止位
    USART_InitStructure.USART_Parity = USART_Parity_No;//无奇偶校验位
    USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;//无硬件数据流控制
    USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx; //收发模式

    USART_InitStructure.USART_BaudRate = bound4;//串口波特率
    USART_Init(UART4, &USART_InitStructure); //初始化串口

    /*串口--4*/
    NVIC_InitStructure.NVIC_IRQChannel = UART4_IRQn;
    NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority=1;
    NVIC_InitStructure.NVIC_IRQChannelSubPriority = 2;
    NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
    NVIC_Init(&NVIC_InitStructure);

    USART_ITConfig(UART4, USART_IT_RXNE, ENABLE);//开启串口接受中断

    USART_Cmd(UART4, ENABLE);                    //使能串口
}



//串口中断服务程序
__attribute__((interrupt("WCH-Interrupt-fast")))
void UART4_IRQHandler(void)
{
    u8 Res;
    if(USART_GetITStatus(UART4, USART_IT_RXNE) != RESET)
    {
        Res =USART_ReceiveData(UART4); //读取接收到的数据
        USART_SendData(UART4, Res);//返回接收的数据
    }
}

 

 

串口5

void uart_init(u32 bound5){
    //GPIO端口设置
    GPIO_InitTypeDef GPIO_InitStructure;
    USART_InitTypeDef USART_InitStructure;
    NVIC_InitTypeDef NVIC_InitStructure;

    RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART2|RCC_APB1Periph_USART3|RCC_APB1Periph_UART4|RCC_APB1Periph_UART5, ENABLE);
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA|RCC_APB2Periph_GPIOB|RCC_APB2Periph_GPIOC|RCC_APB2Periph_GPIOD|RCC_APB2Periph_USART1|RCC_APB2Periph_AFIO , ENABLE);

    //串口引脚
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_12;
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
    GPIO_Init(GPIOC, &GPIO_InitStructure);

    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_2;
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU;
    GPIO_Init(GPIOD, &GPIO_InitStructure);


    //USART 初始化设置
    USART_InitStructure.USART_WordLength = USART_WordLength_8b;//字长为8位数据格式
    USART_InitStructure.USART_StopBits = USART_StopBits_1;//一个停止位
    USART_InitStructure.USART_Parity = USART_Parity_No;//无奇偶校验位
    USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;//无硬件数据流控制
    USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx; //收发模式

    USART_InitStructure.USART_BaudRate = bound5;//串口波特率
    USART_Init(UART5, &USART_InitStructure); //初始化串口

    /*串口--5*/
    NVIC_InitStructure.NVIC_IRQChannel = UART5_IRQn;
    NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority=1;
    NVIC_InitStructure.NVIC_IRQChannelSubPriority = 3;
    NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
    NVIC_Init(&NVIC_InitStructure);

    USART_ITConfig(UART5, USART_IT_RXNE, ENABLE);//开启串口接受中断

    USART_Cmd(UART5, ENABLE);                    //使能串口
}


//串口中断服务程序
__attribute__((interrupt("WCH-Interrupt-fast")))
void UART5_IRQHandler(void)
{
    u8 Res;
    if(USART_GetITStatus(UART5, USART_IT_RXNE) != RESET)
    {
        Res =USART_ReceiveData(UART5); //读取接收到的数据
        USART_SendData(UART5, Res);
    }
}

 

 

串口6,7,8根据串口4,5修改就可以

            TX , RX

串口6(PC0, PC1)

串口7(PC2, PC3)

串口8(PC4, PC5)

 

 

 

我提供了一套标准的数据处理方案

 

 

1,提供的例程是串口1和串口2接收到什么数据就返回什么数据

 

 

 

2,我这边自己实现了延时函数,所以把官方的屏蔽了

 

 

 

 

 

 

 

 

3,printf我这边也改了(中断发送,不会阻塞)

 

 

 

4,串口1和串口2接收数据都是使用环形队列接收

 

 

 

 

 

 

 

4,串口1判断接收完一条数据使用的是自带的空闲中断

 

 

 

5,串口2判断接收完一条数据是使用定时器自定义的空闲时间

 

 

 

 

 

6,串口1发送数据可以使用中断方式

 

标签：USART,CH32V307,NVIC,单片机,InitStructure,Mode,串口,GPIO
来源： https://www.cnblogs.com/yangfengwu/p/16289392.html

本站声明： 1. iCode9 技术分享网（下文简称本站）提供的所有内容，仅供技术学习、探讨和分享；
2. 关于本站的所有留言、评论、转载及引用，纯属内容发起人的个人观点，与本站观点和立场无关；
3. 关于本站的所有言论和文字，纯属内容发起人的个人观点，与本站观点和立场无关；
4. 本站文章均是网友提供，不完全保证技术分享内容的完整性、准确性、时效性、风险性和版权归属；如您发现该文章侵犯了您的权益，可联系我们第一时间进行删除；
5. 本站为非盈利性的个人网站，所有内容不会用来进行牟利，也不会利用任何形式的广告来间接获益，纯粹是为了广大技术爱好者提供技术内容和技术思想的分享性交流网站。

关于我们 | 联系我们 | 留言反馈

专注分享技术，共同学习，共同进步。侵权联系[81616952@qq.com]

Copyright (C)ICode9.com, All Rights Reserved.

ICode9版权所有