首页 > 其他分享> 文章详细

[网络-单臂路由]cisco设备配置

2022-02-03 15:01:45 阅读：193 来源： 互联网

标签：cisco vlan 192.168 Switch exit Router config 路由单臂

拓扑图

网络设备信息：

网络设备配置信息

PC终端配置信息

需求：通过单臂路由的方式PC1与PC2互通

具体配置

交换机1配置：

 1 Switch>en
 2 Switch#configure 
 3 Configuring from terminal, memory, or network [terminal]? 
 4 Enter configuration commands, one per line.  End with CNTL/Z.
 5 Switch(config)#vlan 10
 6 Switch(config-vlan)#exit
 7 Switch(config)#interface  fastEthernet 0/1
 8 Switch(config-if)#switchport mode access 
 9 Switch(config-if)#switchport access vlan 10
10 Switch(config-if)#exit
11 Switch(config)#interface gigabitEthernet 0/1
12 Switch(config-if)#switchport mode trunk 
13 Switch(config-if)#switchport trunk allowed vlan 10
14 Switch(config-if)#exit
15 Switch(config)#exit
16 Switch#
17 %SYS-5-CONFIG_I: Configured from console by console
18 Switch#write
19 Building configuration...
20 [OK]

交换机2配置：

 1 Switch>en
 2 Switch#configure 
 3 Configuring from terminal, memory, or network [terminal]? 
 4 Enter configuration commands, one per line.  End with CNTL/Z.
 5 Switch(config)#vlan 20
 6 Switch(config-vlan)#exit
 7 Switch(config)#interface  fastEthernet 0/2
 8 Switch(config-if)#switchport mode  access 
 9 Switch(config-if)#switchport access vlan 20
10 Switch(config-if)#exit
11 Switch(config)#interface  gigabitEthernet 0/1
12 Switch(config-if)#switchport mode trunk 
13 Switch(config-if)#switchport trunk allowed vlan 20
14 Switch(config-if)#exit
15 Switch(config)#exit
16 Switch#
17 %SYS-5-CONFIG_I: Configured from console by console
18 Switch#write
19 Building configuration...
20 [OK]

路由器配置

 1 Router>en
 2 Router#configure 
 3 Configuring from terminal, memory, or network [terminal]? 
 4 Enter configuration commands, one per line.  End with CNTL/Z.
 5 Router(config)#interface  gigabitEthernet 0/0/1.1
 6 Router(config-subif)#encapsulation dot1Q  10
 7 Router(config-subif)#ip address 192.168.10.254 255.255.255.0
 8 Router(config-subif)#exit
 9 Router(config)#interface  gigabitEthernet 0/0/2.2
10 Router(config-subif)#encapsulation dot1Q 20
11 Router(config-subif)#ip address 192.168.20.254 255.255.255.0
12 Router(config-subif)#exit
13 Router(config)#interface gigabitEthernet 0/0/1
14 Router(config-if)#no shutdown
15 Router(config-if)#exit
16 Router(config)#interface gigabitEthernet 0/0/2
17 Router(config-if)#no shutdown
18 Router(config-if)#exit
15 %SYS-5-CONFIG_I: Configured from console by console
16 Router#write
17 Building configuration...
18 [OK]

测试PC1 ping PC2

 1 C:\>ping 192.168.20.1 
 2 
 3 Pinging 192.168.20.1 with 32 bytes of data:
 4 
 5 Reply from 192.168.20.1: bytes=32 time<1ms TTL=127
 6 Reply from 192.168.20.1: bytes=32 time<1ms TTL=127
 7 Reply from 192.168.20.1: bytes=32 time<1ms TTL=127
 8 Reply from 192.168.20.1: bytes=32 time<1ms TTL=127
 9 
10 Ping statistics for 192.168.20.1:
11     Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
12 Approximate round trip times in milli-seconds:
13     Minimum = 0ms, Maximum = 0ms, Average = 0ms
14 
15 C:\>ping 192.168.20.254
16 
17 Pinging 192.168.20.254 with 32 bytes of data:
18 
19 Reply from 192.168.20.254: bytes=32 time<1ms TTL=255
20 Reply from 192.168.20.254: bytes=32 time<1ms TTL=255
21 Reply from 192.168.20.254: bytes=32 time<1ms TTL=255
22 
23 Ping statistics for 192.168.20.254:
24     Packets: Sent = 3, Received = 3, Lost = 0 (0% loss),
25 Approximate round trip times in milli-seconds:
26     Minimum = 0ms, Maximum = 0ms, Average = 0ms
27 
28 Control-C

标签：cisco,vlan,192.168,Switch,exit,Router,config,路由,单臂
来源： https://www.cnblogs.com/baktomcat/p/15861485.html

本站声明： 1. iCode9 技术分享网（下文简称本站）提供的所有内容，仅供技术学习、探讨和分享；
2. 关于本站的所有留言、评论、转载及引用，纯属内容发起人的个人观点，与本站观点和立场无关；
3. 关于本站的所有言论和文字，纯属内容发起人的个人观点，与本站观点和立场无关；
4. 本站文章均是网友提供，不完全保证技术分享内容的完整性、准确性、时效性、风险性和版权归属；如您发现该文章侵犯了您的权益，可联系我们第一时间进行删除；
5. 本站为非盈利性的个人网站，所有内容不会用来进行牟利，也不会利用任何形式的广告来间接获益，纯粹是为了广大技术爱好者提供技术内容和技术思想的分享性交流网站。

ICode9

[网络-单臂路由]cisco设备配置