标签：IPC land mm denotes 7351 padstack corner Naming hole

INTRODUCTION

 

The padstack consists of combinations of letters and numbers that represent shape, or dimensions of lands on different layers of printed boards or documentation. The name of the padstack needs to represent all the various combinations. These are used in combination with the land pattern conventions defined herein according to the rules established in the IPC-2220 Design standards.

 

The first part of the padstack convention consists of a land shape. There are six basic land shape identifiers. Note: All alphabetical characters are “lower case”. This helps discriminate numeric values.

 

Basic Land Shape Letters

 

c = Circular   

s = Square

r = Rectangle

b = Oblong

u = User Defined Contour (Irregular Shape)

d = D Shape (Square on one end and Circular on the other end)

 

Padstack Defaults

 

• Solder Mask is 1:1 scale of the land size
• Paste Mask is 1:1 scale of the land size
• The Assembly Layer land is 1:1 scale of the land size
• Inner Layer Land is the same shape as the outer layer land
• The Primary and Secondary lands are the same size
• The inner layer land shapes are Circular
• Vias are Circular
• Thermal ID, OD and Spoke Width sizes follow the IPC Level A, B or C
• Plane Clearance Anti-pad size follows the IPC Level A, B or C
• Thermals have 4 spokes
• Mounting Holes are Circular

Note: Every board fabricator’s ability to register solder mask is different.  The 1:1 scale solder mask covers the variation, and so long as manufacturers are building to specs such as IPC-6012 that say you can’t have mis-registration of the solder mask. 

           

Illegal characters that cannot be used (Microsoft requirement) include “ ” , ; : / \ [ ] ( ) . { } * & % # $ ! @ ^ =

 

Examples utilizing the padstack naming convention (all values are in metric units)

Note: Every number goes two places to the right and as many as needed to the left of the decimal

Examples: 1150 = 11.50 mm or 11500 μm, 150 = 1.50 mm or 1500 μm, 15 = 0.15 mm or 150 μm

 

c150h90 where “c” denotes a Circular land with a 1.50 diameter and H denotes a hole size of 0.90

c130_95 Donut pad where “c” denotes a Circular land with a 1.30 OD diameter and 95 denotes the ID diameter

c130_95hn Donut pad - “c” denotes a Circular land with a 1.30 OD diameter and 95 denotes the ID diameter and hn70 denotes hole, non-plated 0.70 diameter
c130_95hn70k147 Donut pad - “c” denotes a Circular land with a 1.30 OD diameter and 95 denotes the ID diameter and hn70 denotes hole, non-plated 0.70 diameter and k147 denotes a keep-out 1.47 diameter

v50h25 where a “v” denotes a via with a 0.50 land (default Circular land) and H denotes a 0.25 hole

s150h90 where “s” denotes a 1.50 Square land and H denotes a hole size of 0.90

s350 where ‘s” denotes a square SMT land size of 3.50

r200_100 where “r” denotes a Rectangular SMT land 2.00 land length X 1.00 land width

b300_150 where “b” denotes a SMT Oblong land size of 3.00 X 1.50

b400_200h100 where “b” denotes an Oblong land size of 4.00 length X 2.00 width and 1.00 hole

d300_150 where “d” denotes land with one circular end and one square end (looks like a D) 3.00 X 1.50

v30h15l1-3 where “v” denotes a 0.30 blind via with 0.15 Hole; 1 is the starting layer, 3 is the end layer

r200_100r5 = Rounded Rectangular 2mm X 1mm X 0.05mm radius corners

r200_100c10 = Chamfered Rectangular 2mm X 1mm X 0.1mm chamfered corners

v30h15l3-6 where “v” denotes a 0.30 buried via with 0.15 Hole; 3 is the starting layer, 6 is the end layer

 

The through hole “IPC-7251 Padstacks.xls” file should be used as the basis for a new chart in IPC-7251 and IPC-7351B.  Note: Draft supporting paragraphs with formula that document the math involved.

It is assumed that the padstack has the same value as the mounted layer size and shape for –

• Inner Layer
• Opposite Side
• Solder Mask
• Solder Paste
• Assembly Layers

It is also assumed that the “Plane Clearance” and “Thermal Relief” data follows the through-hole convention guidelines defined in the IPC-2221 and IPC-2222 standards.

 

Modifiers that are used when padstack features are different than the defaults

 

These are the “Variants” or “Modifiers” that go after the basic padstack naming convention.

These are used when the User needs to change the padstack default values either by a different dimension or a different shape. In instances where shapes are different this becomes a two letter code with the modifier first followed by the land shape letter.

 

n = Non-plated Hole

z = Inner Layer land dimension if different than the land on primary layer

x = Special modifier used alone or following other modifiers for lands on opposite side to primary layer land dimension

t­ = Thermal Relief; if different than IPC standard padstack – tid_od_sw for 4 spoke default      

m = Solder Mask if different than default 1:1 scale of land

p = Solder Paste if different than default 1:1 scale of land

a = Assembly surface land if different than default 1:1 scale of land

y = Plane Clearance (Anti-pad) if the value is different than the Thermal OD

o = Offset Land Origin

k = Keep-out

r = Radius for Rounded Rectangular Land Shape

c = Chamfer for Chamfered Rectangular Land Shape

 

Shape change is the last letter in the string prior to the dimension.

 

 

Other usage of the padstack naming convention

 

USE of letter v: Vias can be named using the padstack naming convention. Because most vias use lands that are circular in shape, the letter V will be used in place of the letter C in the padstack naming convention. If this is not true the modifiers can be added after the letter V to signify shape or dimensional changes to this default.

 

USE of letter w: In addition to Vias the padstack naming convention can also be used for defining mounting holes. The letter W shall be used to define the mounting hole characteristics and any associated lands used for the surface lands (either plated or un-plated)

 

Examples of double character modifiers:

 

ts = Thermal Square; if different than the top side land shape and dimensions

sw = Thermal spoke width

zs = Inner Layer Land Shape is Square (Note: The default is circular)

m0 = No Solder Mask

mxc = Solder Mask Opposite Side Circular

mx0 = Solder Mask Opposite Side No Solder Mask

xc = Opposite Side Circular

vs = Via with Square land

hn = Non-plated Hole

 

Modifier Example for Through-hole:

 

s150h90zs150 = where “s” is Square 1.50 land with 0.90 Hole with 1.50 inner (Z) Layer Square land

c150h90zc150 = where “c” is Circular 1.50 land with 0.90 Hole with 1.50 inner (Z) Layer Circular land

 

Modifier Examples for Vias:

 

vs50h25 where “vs” denotes a 0.50 Square Via with a 0.25 Hole

v50h25xs70 where “v” is 0.50 Circular Via with 0.25 Hole and 0.70 Square land on opposite side

 

Chamfered & Rounded corner modifiers are used to indicate which corner(s) are modified.

Order of precedence has been given to the first 4 modifiers.

 

Modifiers:
bl – bottom left
br – bottom right
ul – upper left
ur – upper right
ulr – upper left & right

blr – bottom left & right

ubl – upper and bottom left

ubr – upper and bottom right

 

Rounded and Chamfered lands in “one corner” Modifier Examples:

 

r100_200rbl50 = rectangular land 1.00 x 2.00 with 0.50 radius for rounded corner in bottom left corner

 

r100_200rbr50 = rectangular land 1.00 x 2.00 with 0.50 radius for rounded corner in bottom right corner

 

r100_200rul50 = rectangular land 1.00 x 2.00 with 0.50 radius for rounded corner in upper left corner

 

r100_200rur50 = rectangular land 1.00 x 2.00 with 0.50 radius for rounded corner in upper right corner

 

r100_200cbl50 = rectangular land 1.00 x 2.00 with 0.50 chamfer for chamfer corner in bottom left corner

 

r100_200cbr50 = rectangular land 1.00 x 2.00 with 0.50 chamfer for chamfer corner in bottom right corne

 

r100_200cul50 = rectangular land 1.00 x 2.00 with 0.50 chamfer for chamfer corner in upper left corner

 

r100_200cur50 = rectangular land 1.00 x 2.00 with 0.50 chamfer for chamfer corner in upper right corner

Examples of a square land with 3 rounded and 1 chamfered corner (for Thermal Pad)

 

s300p190r25cul50 = square 3.00 land, square paste 1.90, corner radius 0.25, upper-left chamfer 0.50

 

s300p190r25cbl50 = square 3.00 land, square paste 1.90, corner radius 0.25, bottom-left chamfer 0.50

 

 

Chamfered and Rounded Rectangular with all four corners chamfered does not need a corner modifier.

 

Modifier Examples with Rounded Rectangle Land Shape:

 

r200_100r50 = rectangular land 2.00 x 1.00 with 0.50 radius for rounded corners in all 4 corners

r200_100c50 = rectangular land 2.00 x 1.00 with 0.50 chamfer for chamfered corners in all 4 corners

 

Examples of a padstack with Circular land with hole using various modifiers

 

c150h90 = Default padstack with a 1.50 circular land with a 0.90 hole (no modifiers used)

 

c150hn90 = Default padstack with a 1.50 circular land with a 0.90 non-plated hole (no modifiers used)

 

c150h90z140 = Inner layer land is smaller than external lands 1.40 or 0.10 smaller

 

c150h90z140x170 = Opposite side land is larger than top side land 1.70 or 0.20 larger

 

c150h90z140x170m165mx185 = Solder mask opening for top and bottom lands 0.15 larger for each

 

c150h90z140x170m165mX185a200 = Assembly drawing land in 0.50 larger than 1.50 primary land

 

c150h90z140x170m165mx185a200y300 = Plane clearance anti-pad diameter is 3.00

 

c150h90z140x170m165mx85 = Solder mask encroachment on opposite land by 0.65 smaller

 

c150h90m165 = adding a solder mask opening of 1.65 diameter or 0.15 larger than land

 

c150h90t150_180_40 = Thermal ID 1.50, OD 1.80, Spoke Width 0.40, Anti-pad 1.80

 

c150h90t150_180_40y200 = Anti-pad 2.00 (because the size is different than the Thermal OD)

 

c150h90t150_180_80_2 = Spoke Width 0.80 with 2 Spokes

 

c150h90m165t150_180_40 = Solder Mask 1.65

 

 

Examples of a padstack with Oblong land with Slotted Hole

 

Sample – b = Oblong Land Shape then “X” dimension (length) then Underscore _ “Y” dimension (width)

 

b400_200h300_100 = Oblong land 4mm length X 2mm width with slotted hole size 3mm X 1mm

 

b400_200hn300_100 = Oblong land 4mm X 2mm with non-plated slotted hole size 3mm X 1mm

 

 

Examples of a SMT padstack land using various modifiers

 

b300_150 = Default padstack with a 3.00 length and 1.50 width land (no modifiers used)

 

b300_150m330_180 = Solder Mask is 0.30 larger than the land on all sides

 

b300_150m330_180p240_140 = Solder Paste is smaller by 0.10 width and 0.60 length

 

b300_150b-50 = Oblong Land 3.0mm X 1.5mm w/Offset Origin negative 0.5mm

 

r400_200po430_230 = Rectangle SMT land 4.00 X 2.00 with a Oblong Solder Paste size of 4.30 X 2.30

 

 

Example of Thermal Pads for QFN, SON, QFP and SOP

Square Configurations

 

s480p4s152 = 4.80mm Square Land with 4 Paste Mask Squares 1.52mm each

 

s480p4s152cul50 = 4.80mm Square Land with 4 Paste Mask Squares 1.52mm each with 0.50mm Chamfer in Upper Left corner

 

s480p4s152cul50r25 = 4.80mm Square Land with 4 Paste Mask Squares 1.52mm each with 0.50mm Chamfer in Upper Left corner with 0.25mm corner Radius

 

Example of a Mounting Hole

 

w700h400z520m720 = This is a Plated Through Mounting hole for a #6-32 screw using a 4.00 diameter hole and having a circular 7.00 land on the primary and secondary side of the board, with a solder mask clearance that is 0.20 larger than the 7.20 land. The internal lands are smaller that the external and are also circular 5.20 in diameter.

 

w700hn400z520m720 = Non-plated version

 

Example of a Local Fiducial for Fine Pitch SMT Components

 

c100m200k200 = Circular Land 1.00 with Solder Mask 2.00 with Keep-out 2.00

s100m200k200 = Square Land 1.00 with Solder Mask 2.00 with Keep-out 2.00

 

Example of Proportional Plated Through-hole padstack

 

c150h100 = 1.5mm circular pad with 1mm hole with 1.5mm solder mask with 1.5mm plane clearance with 1.5mm assembly outline with Thermal Relief w/4 spokes 0.4mm width with ID 1.5mm and OD 1.8mm

 

Example of Proportional Non-plated Through-hole padstack

 

c100hn150 = 1mm circular pad with 1.5mm hole “non-plated” with 1.5mm solder mask with 2.35mm plane clearance with 2.1mm keep-out

标签：IPC,land,mm,denotes,7351,padstack,corner,Naming,hole
来源： https://blog.csdn.net/liuxizhen2009/article/details/88232495

本站声明： 1. iCode9 技术分享网（下文简称本站）提供的所有内容，仅供技术学习、探讨和分享；
2. 关于本站的所有留言、评论、转载及引用，纯属内容发起人的个人观点，与本站观点和立场无关；
3. 关于本站的所有言论和文字，纯属内容发起人的个人观点，与本站观点和立场无关；
4. 本站文章均是网友提供，不完全保证技术分享内容的完整性、准确性、时效性、风险性和版权归属；如您发现该文章侵犯了您的权益，可联系我们第一时间进行删除；
5. 本站为非盈利性的个人网站，所有内容不会用来进行牟利，也不会利用任何形式的广告来间接获益，纯粹是为了广大技术爱好者提供技术内容和技术思想的分享性交流网站。