标签：P2 quit P1 SR over MPLS PE1 PE2 ospf
组网需求
如图1所示:
-
CE1、CE2属于vpna。
-
vpna使用的VPN-target属性为111:1。
配置L3VPN迭代OSPF SR-MPLS BE隧道，保证相同VPN用户之间的安全互访。同时由于公网PE之间存在多条链路，要求数据流量在公网能够进行负载分担。
图1 L3VPN迭代OSPF SR-MPLS BE隧道组网图
配置思路
-
骨干网上配置OSPF实现PE之间的互通。
-
骨干网上使能MPLS，配置Segment Routing，建立SR LSP。使能TI-LFA FRR。
-
PE上配置使能IPv4地址族VPN实例，并把与CE相连的接口和相应的VPN实例绑定。
-
PE之间配置MP-IBGP交换路由信息。
-
CE与PE之间配置EBGP交换路由信息。
操作步骤
1. 配置接口的IP地址
# 配置PE1。
<HUAWEI> system-view
[~HUAWEI] sysname PE1
[*HUAWEI] commit
[~PE1] interface loopback 1
[*PE1-LoopBack1] ip address 1.1.1.9 32
[*PE1-LoopBack1] quit
[*PE1] interface gigabitethernet1/0/0
[*PE1-GigabitEthernet1/0/0] ip address 172.18.1.1 24
[*PE1-GigabitEthernet1/0/0] quit
[*PE1] interface gigabitethernet3/0/0
[*PE1-GigabitEthernet3/0/0] ip address 172.16.1.1 24
[*PE1-GigabitEthernet3/0/0] quit
[*PE1] commit# 配置P1。
<HUAWEI> system-view
[~HUAWEI] sysname P1
[*HUAWEI] commit
[~P1] interface loopback 1
[*P1-LoopBack1] ip address 2.2.2.9 32
[*P1-LoopBack1] quit
[*P1] interface gigabitethernet1/0/0
[*P1-GigabitEthernet1/0/0] ip address 172.16.1.2 24
[*P1-GigabitEthernet1/0/0] quit
[*P1] interface gigabitethernet2/0/0
[*P1-GigabitEthernet2/0/0] ip address 172.17.1.1 24
[*P1-GigabitEthernet2/0/0] quit
[*P1] commit# 配置PE2。
<HUAWEI> system-view
[~HUAWEI] sysname PE2
[*HUAWEI] commit
[~PE2] interface loopback 1
[*PE2-LoopBack1] ip address 3.3.3.9 32
[*PE2-LoopBack1] quit
[*PE2] interface gigabitethernet1/0/0
[*PE2-GigabitEthernet1/0/0] ip address 172.19.1.2 24
[*PE2-GigabitEthernet1/0/0] quit
[*PE2] interface gigabitethernet3/0/0
[*PE2-GigabitEthernet3/0/0] ip address 172.17.1.2 24
[*PE2-GigabitEthernet3/0/0] quit
[*PE2] commit# 配置P2。
<HUAWEI> system-view
[~HUAWEI] sysname P2
[*HUAWEI] commit
[~P2] interface loopback 1
[*P2-LoopBack1] ip address 4.4.4.9 32
[*P2-LoopBack1] quit
[*P2] interface gigabitethernet1/0/0
[*P2-GigabitEthernet1/0/0] ip address 172.18.1.2 24
[*P2-GigabitEthernet1/0/0] quit
[*P2] interface gigabitethernet2/0/0
[*P2-GigabitEthernet2/0/0] ip address 172.19.1.1 24
[*P2-GigabitEthernet2/0/0] quit
[*P2] commit2. 在骨干网上配置IGP协议，实现骨干网PE和P的互通。本例中以OSPF为例进行说明
# 配置PE1。
[~PE1] ospf 1
[*PE1-ospf-1] opaque-capability enable
[*PE1-ospf-1] area 0
[*PE1-ospf-1-area-0.0.0.0] quit
[*PE1-ospf-1] quit
[*PE1] interface loopback 1
[*PE1-LoopBack1] ospf enable 1 area 0
[*PE1-LoopBack1] quit
[*PE1] interface gigabitethernet1/0/0
[*PE1-GigabitEthernet1/0/0] ospf enable 1 area 0
[*PE1-GigabitEthernet1/0/0] quit
[*PE1] interface gigabitethernet3/0/0
[*PE1-GigabitEthernet3/0/0] ospf enable 1 area 0
[*PE1-GigabitEthernet3/0/0] quit
[*PE1] commit# 配置P1。
[~P1] ospf 1
[*P1-ospf-1] opaque-capability enable
[*P1-ospf-1] area 0
[*P1-ospf-1-area-0.0.0.0] quit
[*P1-ospf-1] quit
[*P1] interface loopback 1
[*P1-LoopBack1] ospf enable 1 area 0
[*P1-LoopBack1] quit
[*P1] interface gigabitethernet1/0/0
[*P1-GigabitEthernet1/0/0] ospf enable 1 area 0
[*P1-GigabitEthernet1/0/0] quit
[*P1] interface gigabitethernet2/0/0
[*P1-GigabitEthernet2/0/0] ospf enable 1 area 0
[*P1-GigabitEthernet2/0/0] quit
[*P1] commit# 配置PE2。
[~PE2] ospf 1
[*PE2-ospf-1] opaque-capability enable
[*PE2-ospf-1] area 0
[*PE2-ospf-1-area-0.0.0.0] quit
[*PE2-ospf-1] quit
[*PE2] interface loopback 1
[*PE2-LoopBack1] ospf enable 1 area 0
[*PE2-LoopBack1] quit
[*PE2] interface gigabitethernet3/0/0
[*PE2-GigabitEthernet3/0/0] ospf enable 1 area 0
[*PE2-GigabitEthernet3/0/0] quit
[*PE2] interface gigabitethernet1/0/0
[*PE2-GigabitEthernet1/0/0] ospf enable 1 area 0
[*PE2-GigabitEthernet1/0/0] quit
[*PE2] commit# 配置P2。
[~P2] ospf 1
[*P2-ospf-1] opaque-capability enable
[*P2-ospf-1] area 0
[*P2-ospf-1-area-0.0.0.0] quit
[*P2-ospf-1] quit
[*P2] interface loopback 1
[*P2-LoopBack1] ospf enable 1 area 0
[*P2-LoopBack1] quit
[*P2] interface gigabitethernet1/0/0
[*P2-GigabitEthernet1/0/0] ospf enable 1 area 0
[*P2-GigabitEthernet1/0/0] quit
[*P2] interface gigabitethernet2/0/0
[*P2-GigabitEthernet2/0/0] ospf enable 1 area 0
[*P2-GigabitEthernet2/0/0] quit
[*P2] commit3. （可选）在骨干网上配置MPLS基本能力
当接口下使能OSPF功能后，接口自动使能MPLS能力，所以也可以忽略此步骤。
# 配置PE1。
[~PE1] mpls lsr-id 1.1.1.9
[*PE1] mpls
[*PE1-mpls] commit
[~PE1-mpls] quit# 配置P1。
[~P1] mpls lsr-id 2.2.2.9
[*P1] mpls
[*P1-mpls] commit
[~P1-mpls] quit# 配置PE2。
[~PE2] mpls lsr-id 3.3.3.9
[*PE2] mpls
[*PE2-mpls] commit
[~PE2-mpls] quit# 配置P2。
[~P2] mpls lsr-id 4.4.4.9
[*P2] mpls
[*P2-mpls] commit
[~P2-mpls] quit
4. 在骨干网上配置Segment Routing，同时使能TI-LFA FRR功能
# 配置PE1。
[~PE1] segment-routing
[*PE1-segment-routing] quit
[*PE1] ospf 1
[*PE1-ospf-1] segment-routing mpls
[*PE1-ospf-1] segment-routing global-block 16000 23999
[*PE1-ospf-1] frr
[*PE1-ospf-1-frr] loop-free-alternate
[*PE1-ospf-1-frr] ti-lfa enable
[*PE1-ospf-1-frr] quit
[*PE1-ospf-1] quit
[*PE1] interface loopback 1
[*PE1-LoopBack1] ospf prefix-sid index 10
[*PE1-LoopBack1] quit
[*PE1] commit# 配置P1。
[~P1] segment-routing
[*P1-segment-routing] quit
[*P1] ospf 1
[*P1-ospf-1] segment-routing mpls
[*P1-ospf-1] segment-routing global-block 16000 23999
[*P1-ospf-1] frr
[*P1-ospf-1-frr] loop-free-alternate
[*P1-ospf-1-frr] ti-lfa enable
[*P1-ospf-1-frr] quit
[*P1-ospf-1] quit
[*P1] interface loopback 1
[*P1-LoopBack1] ospf prefix-sid index 20
[*P1-LoopBack1] quit
[*P1] commit# 配置PE2。
[~PE2] segment-routing
[*PE2-segment-routing] quit
[*PE2] ospf 1
[*PE2-ospf-1] segment-routing mpls
[*PE2-ospf-1] segment-routing global-block 16000 23999
[*PE2-ospf-1] frr
[*PE2-ospf-1-frr] loop-free-alternate
[*PE2-ospf-1-frr] ti-lfa enable
[*PE2-ospf-1-frr] quit
[*PE2-ospf-1] quit
[*PE2] interface loopback 1
[*PE2-LoopBack1] ospf prefix-sid index 30
[*PE2-LoopBack1] quit
[*PE2] commit# 配置P2。
[~P2] segment-routing
[*P2-segment-routing] quit
[*P2] ospf 1
[*P2-ospf-1] segment-routing mpls
[*P2-ospf-1] segment-routing global-block 16000 23999
[*P2-ospf-1] frr
[*P2-ospf-1-frr] loop-free-alternate
[*P2-ospf-1-frr] ti-lfa enable
[*P2-ospf-1-frr] quit
[*P2-ospf-1] quit
[*P2] interface loopback 1
[*P2-LoopBack1] ospf prefix-sid index 40
[*P2-LoopBack1] quit
[*P2] commit# 配置完成后，在PE设备上执行display tunnel-info all命令，可以看到SR LSP已建立。以PE1的显示为例。
[~PE1] display tunnel-info all
Tunnel ID Type Destination Status
----------------------------------------------------------------------------------------
0x000000002900000003 srbe-lsp 4.4.4.9 UP
0x000000002900000004 srbe-lsp 2.2.2.9 UP
0x000000002900000005 srbe-lsp 3.3.3.9 UP # 在PE1上使用Ping检测SR LSP连通性，例如：
[~PE1] ping lsp segment-routing ip 3.3.3.9 32 version draft2
LSP PING FEC: SEGMENT ROUTING IPV4 PREFIX 3.3.3.9/32 : 100 data bytes, press CTRL_C to break
Reply from 3.3.3.9: bytes=100 Sequence=1 time=256 ms
Reply from 3.3.3.9: bytes=100 Sequence=2 time=3 ms
Reply from 3.3.3.9: bytes=100 Sequence=3 time=4 ms
Reply from 3.3.3.9: bytes=100 Sequence=4 time=4 ms
Reply from 3.3.3.9: bytes=100 Sequence=5 time=4 ms
--- FEC: SEGMENT ROUTING IPV4 PREFIX 3.3.3.9/32 ping statistics ---
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 3/54/256 ms5. 在PE之间建立MP-IBGP对等体关系
# 配置PE1。
[~PE1] bgp 100
[~PE1-bgp] peer 3.3.3.9 as-number 100
[*PE1-bgp] peer 3.3.3.9 connect-interface loopback 1
[*PE1-bgp] ipv4-family vpnv4
[*PE1-bgp-af-vpnv4] peer 3.3.3.9 enable
[*PE1-bgp-af-vpnv4] commit
[~PE1-bgp-af-vpnv4] quit
[~PE1-bgp] quit# 配置PE2。
[~PE2] bgp 100
[~PE2-bgp] peer 1.1.1.9 as-number 100
[*PE2-bgp] peer 1.1.1.9 connect-interface loopback 1
[*PE2-bgp] ipv4-family vpnv4
[*PE2-bgp-af-vpnv4] peer 1.1.1.9 enable
[*PE2-bgp-af-vpnv4] commit
[~PE2-bgp-af-vpnv4] quit
[~PE2-bgp] quit配置完成后，在PE设备上执行display bgp peer或display bgp vpnv4 all peer命令，可以看到PE之间的BGP对等体关系已建立，并达到Established状态。以PE1的显示为例。
[~PE1] display bgp peer
BGP local router ID : 1.1.1.9
Local AS number : 100
Total number of peers : 1 Peers in established state : 1
Peer V AS MsgRcvd MsgSent OutQ Up/Down State PrefRcv
3.3.3.9 4 100 5 5 0 00:00:12 Established 0
[~PE1] display bgp vpnv4 all peer
BGP local router ID : 1.1.1.9
Local AS number : 100
Total number of peers : 1 Peers in established state : 1
Peer V AS MsgRcvd MsgSent OutQ Up/Down State PrefRcv
3.3.3.9 4 100 12 18 0 00:09:38 Established 16. 在PE设备上配置使能IPv4地址族的VPN实例，将CE接入PE
# 配置PE1。
[~PE1] ip vpn-instance vpna
[*PE1-vpn-instance-vpna] ipv4-family
[*PE1-vpn-instance-vpna-af-ipv4] route-distinguisher 100:1
[*PE1-vpn-instance-vpna-af-ipv4] vpn-target 111:1 both
[*PE1-vpn-instance-vpna-af-ipv4] quit
[*PE1-vpn-instance-vpna] quit
[*PE1] interface gigabitethernet2/0/0
[*PE1-GigabitEthernet2/0/0] ip binding vpn-instance vpna
[*PE1-GigabitEthernet2/0/0] ip address 10.1.1.2 24
[*PE1-GigabitEthernet2/0/0] quit
[*PE1] commit# 配置PE2。
[~PE2] ip vpn-instance vpna
[*PE2-vpn-instance-vpna] ipv4-family
[*PE2-vpn-instance-vpna-af-ipv4] route-distinguisher 200:1
[*PE2-vpn-instance-vpna-af-ipv4] vpn-target 111:1 both
[*PE2-vpn-instance-vpna-af-ipv4] quit
[*PE2-vpn-instance-vpna] quit
[*PE2] interface gigabitethernet2/0/0
[*PE2-GigabitEthernet2/0/0] ip binding vpn-instance vpna
[*PE2-GigabitEthernet2/0/0] ip address 10.2.1.2 24
[*PE2-GigabitEthernet2/0/0] quit
[*PE2] commit# 按图1配置各CE的接口IP地址，配置过程请参见后面的配置文件。
配置完成后，在PE设备上执行display ip vpn-instance verbose命令可以看到VPN实例的配置情况。各PE能ping通自己接入的CE。
7. 在PE设备上配置隧道选择策略，优选SR LSP
# 配置PE1。
[~PE1] tunnel-policy p1
[*PE1-tunnel-policy-p1] tunnel select-seq sr-lsp load-balance-number 2
[*PE1-tunnel-policy-p1] quit
[*PE1] commit
[~PE1] ip vpn-instance vpna
[*PE1-vpn-instance-vpna] ipv4-family
[*PE1-vpn-instance-vpna-af-ipv4] tnl-policy p1
[*PE1-vpn-instance-vpna-af-ipv4] quit
[*PE1-vpn-instance-vpna] quit
[*PE1] commit# 配置PE2。
[~PE2] tunnel-policy p1
[*PE2-tunnel-policy-p1] tunnel select-seq sr-lsp load-balance-number 2
[*PE2-tunnel-policy-p1] quit
[*PE2] commit
[~PE2] ip vpn-instance vpna
[*PE2-vpn-instance-vpna] ipv4-family
[*PE2-vpn-instance-vpna-af-ipv4] tnl-policy p1
[*PE2-vpn-instance-vpna-af-ipv4] quit
[*PE2-vpn-instance-vpna] quit
[*PE2] commit8. 在PE与CE之间建立EBGP对等体关系
# 配置CE1。
<HUAWEI> system-view
[~HUAWEI] sysname CE1
[*HUAWEI] commit
[~CE1] interface loopback 1
[*CE1-LoopBack1] ip address 10.11.1.1 32
[*CE1-LoopBack1] quit
[*CE1] interface gigabitethernet1/0/0
[*CE1-GigabitEthernet1/0/0] ip address 10.1.1.1 24
[*CE1-GigabitEthernet1/0/0] quit
[*CE1] bgp 65410
[*CE1-bgp] peer 10.1.1.2 as-number 100
[*CE1-bgp] network 10.11.1.1 32
[*CE1-bgp] quit
[*CE1] commit# 配置PE1。
[~PE1] bgp 100
[~PE1-bgp] ipv4-family vpn-instance vpna
[*PE1-bgp-vpna] peer 10.1.1.1 as-number 65410
[*PE1-bgp-vpna] commit
[~PE1-bgp-vpna] quit
[~PE1-bgp] quit配置完成后，在PE设备上执行display bgp vpnv4 vpn-instance peer命令，可以看到PE与CE之间的BGP对等体关系已建立，并达到Established状态。
以PE1与CE1的对等体关系为例：
[~PE1] display bgp vpnv4 vpn-instance vpna peer
BGP local router ID : 1.1.1.9
Local AS number : 100
VPN-Instance vpna, Router ID 1.1.1.9:
Total number of peers : 1 Peers in established state : 1
Peer V AS MsgRcvd MsgSent OutQ Up/Down State PrefRcv
10.1.1.1 4 65410 19 18 0 00:12:39 Established 19. 检查配置结果
在PE设备上执行display ip routing-table vpn-instance命令，可以看到去往CE上的Loopback接口路由。
以PE1的显示为例：
[~PE1] display ip routing-table vpn-instance vpna
Route Flags: R - relay, D - download to fib, T - to vpn-instance, B - black hole route
------------------------------------------------------------------------------
Routing Table: vpna
Destinations : 7 Routes : 7
Destination/Mask Proto Pre Cost Flags NextHop Interface
10.1.1.0/24 Direct 0 0 D 10.1.1.2 GigabitEthernet1/0/0
10.1.1.2/32 Direct 0 0 D 127.0.0.1 GigabitEthernet1/0/0
10.1.1.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet1/0/0
10.11.1.1/32 EBGP 255 0 RD 10.1.1.1 GigabitEthernet1/0/0
10.22.2.2/32 IBGP 255 0 RD 3.3.3.9 GigabitEthernet1/0/0
IBGP 255 0 RD 3.3.3.9 GigabitEthernet3/0/0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0同一VPN的CE能够相互Ping通，例如：CE1能够Ping通CE2（10.22.2.2）。
[~CE1] ping -a 10.11.1.1 10.22.2.2
PING 10.22.2.2: 56 data bytes, press CTRL_C to break
Reply from 10.22.2.2: bytes=56 Sequence=1 ttl=252 time=428 ms
Reply from 10.22.2.2: bytes=56 Sequence=2 ttl=252 time=4 ms
Reply from 10.22.2.2: bytes=56 Sequence=3 ttl=252 time=5 ms
Reply from 10.22.2.2: bytes=56 Sequence=4 ttl=252 time=3 ms
Reply from 10.22.2.2: bytes=56 Sequence=5 ttl=252 time=4 ms
--- 10.22.2.2 ping statistics ---
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 3/88/428 ms标签：P2,quit,P1,SR,over,MPLS,PE1,PE2,ospf 来源： https://blog.csdn.net/guolianggsta/article/details/122616596
本站声明： 1. iCode9 技术分享网（下文简称本站）提供的所有内容，仅供技术学习、探讨和分享； 2. 关于本站的所有留言、评论、转载及引用，纯属内容发起人的个人观点，与本站观点和立场无关； 3. 关于本站的所有言论和文字，纯属内容发起人的个人观点，与本站观点和立场无关； 4. 本站文章均是网友提供，不完全保证技术分享内容的完整性、准确性、时效性、风险性和版权归属；如您发现该文章侵犯了您的权益，可联系我们第一时间进行删除； 5. 本站为非盈利性的个人网站，所有内容不会用来进行牟利，也不会利用任何形式的广告来间接获益，纯粹是为了广大技术爱好者提供技术内容和技术思想的分享性交流网站。