标签：10.1 r4 32 route GigabitEthernet 发布 policy OSPF
要求:
1.如图搭建网络拓扑，所有路由器各自创建一个环回接口，合理规划IP地址
2.R1-R2-R3-R4-R6之间使用OSPF协议，R4- R5-R6之间使用RIP协议
3.R1环回重发布方式引入OSPF网络
4.R4/R6上进行双点双向重发布
5.分析网络中出现路由环路的原因
6.路由优化，全网可达
R1环回重发布方式引入OSPF网络
在R1上写route-policy列表重发布R1UBRL0空的环回
[r1-route-policy]if-ma
[r1-route-policy]if-match int lo0
[r1-route-policy]q
[r1]ospf
[r1-ospf-1]imp
[r1-ospf-1]import-route dir rou
[r1-ospf-1]import-route dir route-policy ccie
[r1-ospf-1]dis this
[V200R003C00]
#
ospf 1 router-id 91.1.1.1
import-route direct route-policy ccie
area 0.0.0.0
network 10.1.1.1 0.0.0.0
area 0.0.0.1
#
return
[r1]dis ospf lsdb
OSPF Process 1 with Router ID 91.1.1.1
Link State Database
Area: 0.0.0.0
Type LinkState ID AdvRouter Age Len Sequence Metric
Router 94.4.4.4 94.4.4.4 1349 48 80000004 0
Router 92.2.2.2 92.2.2.2 1471 60 8000000B 0
Router 96.6.6.6 96.6.6.6 1283 48 80000004 0
Router 91.1.1.1 91.1.1.1 50 36 80000004 1
Router 93.3.3.3 93.3.3.3 1280 72 8000000E 0
Network 10.1.5.1 93.3.3.3 1280 32 80000002 0
Network 10.1.3.1 93.3.3.3 1353 32 80000002 0
Network 10.1.2.1 92.2.2.2 1618 32 80000002 0
Network 10.1.1.2 92.2.2.2 1471 32 80000002 0
Area: 0.0.0.1
AS External Database
Type LinkState ID AdvRouter Age Len Sequence Metric
External 1.1.1.0 91.1.1.1 50 36 80000001 1R4/R6上进行双点双向重发布
[r4]rip
[r4-rip-1]im
[r4-rip-1]import-route ospf 1
[r4-rip-1]ospf 1
[r4-ospf-1]om
[r4-ospf-1]im
[r4-ospf-1]import-route rip 1[r6]ospf
[r6-ospf-1]im
[r6-ospf-1]import-route rip 1
[r6-ospf-1]
[r6-ospf-1]rip
[r6-rip-1]im
[r6-rip-1]import-route ospf 1
[r6-rip-1]
在R3上学习到了R5R6的路由信息
R3的路由表
[r3]dis ospf lsdb
OSPF Process 1 with Router ID 93.3.3.3
Link State Database
Area: 0.0.0.0
Type LinkState ID AdvRouter Age Len Sequence Metric
Router 94.4.4.4 94.4.4.4 737 48 80000008 0
Router 92.2.2.2 92.2.2.2 1387 60 8000000E 0
Router 96.6.6.6 96.6.6.6 493 48 80000008 0
Router 91.1.1.1 91.1.1.1 1767 36 80000006 1
Router 93.3.3.3 93.3.3.3 1194 72 80000011 0
Network 10.1.5.1 93.3.3.3 1194 32 80000005 0
Network 10.1.3.1 93.3.3.3 1266 32 80000005 0
Network 10.1.2.1 92.2.2.2 1534 32 80000005 0
Network 10.1.1.2 92.2.2.2 1387 32 80000005 0
AS External Database
Type LinkState ID AdvRouter Age Len Sequence Metric
External 6.6.6.0 96.6.6.6 493 36 80000003 1
External 4.4.4.0 94.4.4.4 737 36 80000003 1
External 5.0.0.0 94.4.4.4 737 36 80000003 1
External 5.0.0.0 96.6.6.6 493 36 80000003 1
External 10.1.6.0 94.4.4.4 737 36 80000003 1
External 10.1.6.0 96.6.6.6 493 36 80000003 1
External 10.1.4.0 94.4.4.4 737 36 80000003 1
External 10.1.4.0 96.6.6.6 493 36 80000003 1
External 10.1.5.0 96.6.6.6 493 36 80000003 1
External 10.1.3.0 94.4.4.4 737 36 80000003 1
External 1.1.1.0 91.1.1.1 1767 36 80000003 1
这样做双点双向重发布一定会出环，这是R3的路由表1.1.1.0/24的下一跳本应该是10.1.1.1但是在R3的路由表上却是10.1.2.1的下一跳。1.1.1.0/24作为在R1重发布的路由优先级本应该是150在R4上通过重发布进入了rip但是在R6通过RIP学习到的R1环回比150小所以在R6上吧原有的ospf路由信息删除了又通过R6上的重发布把R1的环回以外部路由重新发布到ospf当中所以优先级又变为150但此时R3和R6的cost的值是1所以产生了环路这里的cost值本应该是R1-R3的也就是COST=2所以因为路由回馈出现了环路。
再就是出现本不应该有的负载均衡
在 R6上
[r6]route-policy hcip permit node 10
Info: New Sequence of this List.
[r6-route-policy]if-
[r6-route-policy]if-match ip
[r6-route-policy]if-match ip-
[r6-route-policy]if-match ip-prefix hcip
[r6-route-policy]app
[r6-route-policy]apply cost 100
[r6-route-policy]rou
[r6-route-policy]q
[r6]rou
[r6]route-
[r6]route-policy hcip per
[r6]route-policy hcip permit node 20
Info: New Sequence of this List.
[r6-route-policy]q
[r6]rip
[r6-rip-1]im
[r6-rip-1]import-route ospf 1 ro
[r6-rip-1]import-route ospf 1 route-policy hcip在R5上查看10.1.4.0是否还存在负载均衡
原来
4.0.0.0/8 RIP 100 1 D 10.1.4.1 GigabitEthernet
0/0/1
RIP 100 1 D 10.1.6.1 GigabitEthernet
现在
10.1.4.0/24 Direct 0 0 D 10.1.4.2 GigabitEthernet
0/0/1
在R4上增加metric值
rror: Wrong parameter found at '^' position.
[r4]acl 2000
[r4-acl-basic-2000]ru
[r4-acl-basic-2000]rule pe
[r4-acl-basic-2000]rule permit so
[r4-acl-basic-2000]rule permit source 10.1.5.0 0
[r4-acl-basic-2000]int g0/0/0
[r4-GigabitEthernet0/0/0]rip me
[r4-GigabitEthernet0/0/0]rip metric
[r4-GigabitEthernet0/0/0]rip metricout 2000 100
^
Error: Wrong parameter found at '^' position.
[r4-GigabitEthernet0/0/0]rip metricout 2000 3
原来
10.1.5.0/24 RIP 100 1 D 10.1.6.1 GigabitEthernet
0/0/0
RIP 100 1 D 10.1.4.1 GigabitEthernet
现在
10.1.5.0/24 RIP 100 1 D 10.1.6.1 GigabitEthernet
0/0/0
R3的负载均衡
R3上用route-policy
[r4]ip ip-
[r4]ip ip-prefix aa pe
[r4]ip ip-prefix aa permit 5.0.0.0 8
[r4]ip ip-prefix aa permit 10.1.6.0 24
[r4]rou
[r4]route-
[r4]route-policy aa pe
[r4]route-policy aa permit node 10
Info: New Sequence of this List.
[r4-route-policy]if-
[r4-route-policy]if-match ip-
[r4-route-policy]if-match ip-prefix aa
[r4-route-policy]app
[r4-route-policy]apply co
[r4-route-policy]q
[r4] undo ip ip-prefix aa permit 10.1.6.0 24
^
Error:Too many parameters found at '^' position.
[r4]undo ip ip-prefix aa
[r4]ip ip
[r4]ip ip-
[r4]ip ip-prefix c1 pe
[r4]ip ip-prefix c1 permit 5.0.0.0 8
[r4]ip ip-prefix c2 permit 10.1.6.0 24
[r4]rou
[r4]route-
[r4]route-policy c pe
[r4]route-policy c permit node 10
Info: New Sequence of this List.
[r4-route-policy]if-
[r4-route-policy]if-match ip-
[r4-route-policy]if-match ip-prefix c1
[r4-route-policy]ap
[r4-route-policy]apply c
[r4-route-policy]apply cos
[r4-route-policy]apply cost-type t
[r4-route-policy]apply cost-type type-1
[r4-route-policy]q
[r4]ro
[r4]route-policy c pe
[r4]route-policy c permit node 20
Info: New Sequence of this List.
[r4-route-policy]if-
[r4-route-policy]if-match ip -p
[r4-route-policy]if-match ip-
[r4-route-policy]if-match ip-prefix c2
[r4-route-policy]a
[r4-route-policy]applycos
[r4-route-policy]apply cos
[r4-route-policy]apply cost-type t
[r4-route-policy]apply cost 3
[r4-route-policy]q
[r4]ro
[r4]route-policy c pe
[r4]route-policy c permit node 30
Info: New Sequence of this List.
[r4-route-policy]q
[r4]ospf
[r4-ospf-1]im
[r4-ospf-1]import-route rip 1 ro
[r4-ospf-1]import-route rip 1 route-policy c
[r4-ospf-1]q
[r4]dis ip r
[r4]dis ip rd-filter
[r4]dis ip rou
[r4]dis ip routing-table
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: Public
Destinations : 23 Routes : 23
Destination/Mask Proto Pre Cost Flags NextHop Interface
1.1.1.0/24 O_ASE 150 1 D 10.1.3.1 GigabitEthernet
0/0/1
2.2.2.2/32 OSPF 10 2 D 10.1.3.1 GigabitEthernet
0/0/1
3.3.3.3/32 OSPF 10 1 D 10.1.3.1 GigabitEthernet
0/0/1
4.4.4.0/24 Direct 0 0 D 4.4.4.4 LoopBack0
4.4.4.4/32 Direct 0 0 D 127.0.0.1 LoopBack0
4.4.4.255/32 Direct 0 0 D 127.0.0.1 LoopBack0
5.0.0.0/8 RIP 100 1 D 10.1.4.2 GigabitEthernet
0/0/0
6.6.6.0/24 O_ASE 150 1 D 10.1.3.1 GigabitEthernet
0/0/1
6.6.6.6/32 OSPF 10 2 D 10.1.3.1 GigabitEthernet
0/0/1
10.1.1.0/24 OSPF 10 3 D 10.1.3.1 GigabitEthernet
0/0/1
10.1.2.0/24 OSPF 10 2 D 10.1.3.1 GigabitEthernet
0/0/1
10.1.3.0/24 Direct 0 0 D 10.1.3.2 GigabitEthernet
0/0/1
10.1.3.2/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1
10.1.3.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1
10.1.4.0/24 Direct 0 0 D 10.1.4.1 GigabitEthernet
0/0/0
10.1.4.1/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/0
10.1.4.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/0
10.1.5.0/24 OSPF 10 2 D 10.1.3.1 GigabitEthernet
0/0/1
10.1.6.0/24 RIP 100 1 D 10.1.4.2 GigabitEthernet
0/0/0
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
[r4]ip ip-
[r4]ip ip-prefix c3 pe
[r4]ip ip-prefix c3 permit 10.1.4.0 24
[r4]rou
[r4]route-
[r4]route-policy c per
[r4]route-policy c permit node 30
Info: You are overwriting this sequence.
[r4-route-policy]if-
[r4-route-policy]if-match ip-
[r4-route-policy]if-match ip-prefix c3
[r4-route-policy]apply cost 3
[r4-route-policy]q原来
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: Public
Destinations : 26 Routes : 29
Destination/Mask Proto Pre Cost Flags NextHop Interface
1.1.1.0/24 O_ASE 150 1 D 10.1.2.1 GigabitEthernet
0/0/1
2.2.2.2/32 OSPF 10 1 D 10.1.2.1 GigabitEthernet
0/0/1
3.3.3.0/24 Direct 0 0 D 3.3.3.3 LoopBack0
3.3.3.3/32 Direct 0 0 D 127.0.0.1 LoopBack0
3.3.3.255/32 Direct 0 0 D 127.0.0.1 LoopBack0
4.4.4.0/24 O_ASE 150 1 D 10.1.3.2 GigabitEthernet
0/0/0
4.4.4.4/32 OSPF 10 1 D 10.1.3.2 GigabitEthernet
0/0/0
5.0.0.0/8 O_ASE 150 1 D 10.1.3.2 GigabitEthernet
0/0/0
O_ASE 150 1 D 10.1.5.2 GigabitEthernet
0/0/2
6.6.6.0/24 O_ASE 150 1 D 10.1.5.2 GigabitEthernet
0/0/2
6.6.6.6/32 OSPF 10 1 D 10.1.5.2 GigabitEthernet
0/0/2
10.1.1.0/24 OSPF 10 2 D 10.1.2.1 GigabitEthernet
0/0/1
10.1.2.0/24 Direct 0 0 D 10.1.2.2 GigabitEthernet
0/0/1
10.1.2.2/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1
10.1.2.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1
10.1.3.0/24 Direct 0 0 D 10.1.3.1 GigabitEthernet
0/0/0
10.1.3.1/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/0
10.1.3.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/0
10.1.4.0/24 O_ASE 150 1 D 10.1.3.2 GigabitEthernet
0/0/0
O_ASE 150 1 D 10.1.5.2 GigabitEthernet
0/0/2
10.1.5.0/24 Direct 0 0 D 10.1.5.1 GigabitEthernet
0/0/2
10.1.5.1/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/2
10.1.5.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/2
10.1.6.0/24 O_ASE 150 1 D 10.1.3.2 GigabitEthernet
0/0/0
O_ASE 150 1 D 10.1.5.2 GigabitEthernet
0/0/2
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
路由优化后
Routing Tables: Public
Destinations : 25 Routes : 25
Destination/Mask Proto Pre Cost Flags NextHop Interface
1.1.1.0/24 O_ASE 150 1 D 10.1.2.1 GigabitEthernet
0/0/1
2.2.2.2/32 OSPF 10 1 D 10.1.2.1 GigabitEthernet
0/0/1
3.3.3.0/24 Direct 0 0 D 3.3.3.3 LoopBack0
3.3.3.3/32 Direct 0 0 D 127.0.0.1 LoopBack0
3.3.3.255/32 Direct 0 0 D 127.0.0.1 LoopBack0
4.4.4.4/32 OSPF 10 1 D 10.1.3.2 GigabitEthernet
0/0/0
5.0.0.0/8 O_ASE 150 2 D 10.1.3.2 GigabitEthernet
0/0/0
6.6.6.0/24 O_ASE 150 1 D 10.1.5.2 GigabitEthernet
0/0/2
6.6.6.6/32 OSPF 10 1 D 10.1.5.2 GigabitEthernet
0/0/2
10.1.1.0/24 OSPF 10 2 D 10.1.2.1 GigabitEthernet
0/0/1
10.1.2.0/24 Direct 0 0 D 10.1.2.2 GigabitEthernet
0/0/1
10.1.2.2/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1
10.1.2.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1
10.1.3.0/24 Direct 0 0 D 10.1.3.1 GigabitEthernet
0/0/0
10.1.3.1/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/0
10.1.3.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/0
10.1.4.0/24 O_ASE 150 1 D 10.1.5.2 GigabitEthernet
0/0/2
10.1.5.0/24 Direct 0 0 D 10.1.5.1 GigabitEthernet
0/0/2
10.1.5.1/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/2
10.1.5.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/2
10.1.6.0/24 O_ASE 150 1 D 10.1.5.2 GigabitEthernet
0/0/2
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
---- More ----1.1.1.0的下一跳恢复正常，实验完成。
标签：10.1,r4,32,route,GigabitEthernet,发布,policy,OSPF 来源： https://blog.csdn.net/helloword1997/article/details/119297319
本站声明： 1. iCode9 技术分享网（下文简称本站）提供的所有内容，仅供技术学习、探讨和分享； 2. 关于本站的所有留言、评论、转载及引用，纯属内容发起人的个人观点，与本站观点和立场无关； 3. 关于本站的所有言论和文字，纯属内容发起人的个人观点，与本站观点和立场无关； 4. 本站文章均是网友提供，不完全保证技术分享内容的完整性、准确性、时效性、风险性和版权归属；如您发现该文章侵犯了您的权益，可联系我们第一时间进行删除； 5. 本站为非盈利性的个人网站，所有内容不会用来进行牟利，也不会利用任何形式的广告来间接获益，纯粹是为了广大技术爱好者提供技术内容和技术思想的分享性交流网站。