标签：AC 5.3 GOTO 两圆 CART 10.0000 FA 0.0000 2.0000
要注意的是，如果您使用一个特征的触测点，必须被以相同半径的测头测量。
1.对于RationalDMIS 7.1 :
F(CIR1)=FEAT/CIRCLE,INNER,CART,-0.0000,-0.0000,-10.0000,0.0000,0.0000,1.0000, 30.0000
$$ Measurement points are created through nominal points
MEAS/CIRCLE, F(CIR1), 5
GOTO/CART, 0.0000, -0.0000, 6.0000
GOTO/CART, -12.0000, 0.0000, 6.0000
GOTO/CART, -12.0000, 0.0000, 5.0000
PTMEAS/CART, -15.0000, 0.0000, -10.0000, 1.0000, 0.0000, 0.0000
GOTO/CART, -11.4127, 3.7082, -10.0000
GOTO/CART, -9.7082, 7.0534, -10.0000
GOTO/CART, -7.0534, 9.7082, -10.0000
PTMEAS/CART, -4.6353, 14.2658, -10.0000, 0.3090, -0.9511, 0.0000
GOTO/CART, 0.0000, 12.0000, -10.0000
GOTO/CART, 3.7082, 11.4127, -10.0000
GOTO/CART, 7.0534, 9.7082, -10.0000
PTMEAS/CART, 12.1353, 8.8168, -10.0000, -0.8090, -0.5878, -0.0000
GOTO/CART, 11.4127, 3.7082, -10.0000
GOTO/CART, 12.0000, 0.0000, -10.0000
GOTO/CART, 11.4127, -3.7082, -10.0000
PTMEAS/CART, 12.1353, -8.8168, -10.0000, -0.8090, 0.5878, 0.0000
GOTO/CART, 7.0534, -9.7082, -10.0000
GOTO/CART, 3.7082, -11.4127, -10.0000
GOTO/CART, 0.0000, -12.0000, -10.0000
PTMEAS/CART, -4.6353, -14.2658, -10.0000, 0.3090, 0.9511, 0.0000
GOTO/CART, -3.7082, -11.4127, 5.0000
ENDMES
F(CIR2)=FEAT/CIRCLE,INNER,CART,-0.0000,-0.0000,-2.0000,0.0000,0.0000,1.0000, 30.0000
$$ Measurement points are created through nominal points
MEAS/CIRCLE, F(CIR2), 5
GOTO/CART, -3.7082, -11.4127, 14.0000
GOTO/CART, -12.0000, 0.0000, 14.0000
GOTO/CART, -12.0000, 0.0000, 13.0000
PTMEAS/CART, -15.0000, 0.0000, -2.0000, 1.0000, 0.0000, 0.0000
GOTO/CART, -11.4127, 3.7082, -2.0000
GOTO/CART, -9.7082, 7.0534, -2.0000
GOTO/CART, -7.0534, 9.7082, -2.0000
PTMEAS/CART, -4.6353, 14.2658, -2.0000, 0.3090, -0.9511, 0.0000
GOTO/CART, 0.0000, 12.0000, -2.0000
GOTO/CART, 3.7082, 11.4127, -2.0000
GOTO/CART, 7.0534, 9.7082, -2.0000
PTMEAS/CART, 12.1353, 8.8168, -2.0000, -0.8090, -0.5878, -0.0000
GOTO/CART, 11.4127, 3.7082, -2.0000
GOTO/CART, 12.0000, 0.0000, -2.0000
GOTO/CART, 11.4127, -3.7082, -2.0000
PTMEAS/CART, 12.1353, -8.8168, -2.0000, -0.8090, 0.5878, 0.0000
GOTO/CART, 7.0534, -9.7082, -2.0000
GOTO/CART, 3.7082, -11.4127, -2.0000
GOTO/CART, 0.0000, -12.0000, -2.0000
PTMEAS/CART, -4.6353, -14.2658, -2.0000, 0.3090, 0.9511, 0.0000
GOTO/CART, -3.7082, -11.4127, 13.0000
ENDMES
F(CYL_BF1)=FEAT/CYLNDR,OUTER,CART,0.0000,-0.0000,-6.0000,0.0000,0.0000,1.0000, 30.0000, 8.0000
CONST/CYLNDR,F(CYL_BF1),BF,FA(CIR1)[1],FA(CIR1)[2],FA(CIR1)[3],FA(CIR1)[4],FA(CIR1)[5],FA(CIR2)[1],FA(CIR2)[2],FA(CIR2)[3],FA(CIR2)[4],FA(CIR2)[5]
或：
F(CYL_BF1)=FEAT/CYLNDR,OUTER,CART,0.0000,-0.0000,-6.0000,0.0000,0.0000,1.0000, 30.0000, 8.0000
CONST/CYLNDR,F(CYL_BF1),BF,FA(CIR1)[1,5],FA(CIR2)[1,5]
2.对于AC-DMIS 5.3
DEFINE CYLINDER 组合圆柱-0
TOL("X",0.0000,0.0000,-0.0000)
TOL("Y",0.0000,0.0000,-0.0000)
TOL("Z",0.0000,0.0000,-0.0000)
TOL("A1",0.000000,0.0000,-0.0000)
TOL("A2",0.000000,0.0000,-0.0000)
TOL("A3",0.000000,0.0000,-0.0000)
TOL("DIA",0.0000,0.0000,-0.0000)
TOL("F",0.0000,0.0000,0.0000)
ADD-COMBINATION("圆-1")
ADD-COMBINATION("圆-2")
INOUT-GEOMETRY(-1)
CALCULATE-TYPE(0)
IS-MEASURE-PNTS(0)
CE-CYLINDER("组合圆柱-0",2)
ENDDEF
3.对于LK CAMIO（MODUS）来说如下：
DECL/GLOBAL,REAL,Pts1
DECL/GLOBAL,REAL,Pts2
$$ Collect points from feature
Pts1=VALUE/FA(CIR001),PTDATA
$$ Collect points from feature
Pts2=VALUE/FA(CIR002),PTDATA
F(CylinderName)=FEAT/CYLNDR,INNER,CART,0,0,0,0,1,0,75.1
CONST/CYLNDR,F(CylinderName),BF,FA(CIR001)[1,Pts1],FA(CIR002)[1,Pts2]
if a feature has been measured with point buffering enabled, by a PTBUFF/ON statement, then its individual point data can be referenced by appending the [n] option to F(label) or FA(label), where n is the point index from the feature's programmed PTMEAS statements. When the index [n] option for specifying point data is used, the current probe compensation state shall determine whether probe compensation will be applied to the specified data points during the feature construction, as if the constructed feature were measured with that point data with the MEAS or RMEAS statements. If the best fit feature is constructed with point buffering enabled, by a PTBUFF/ON statement, then the individual point data is copied to the point buffer of the constructed feature and is then accessible with the [n] point data index as if it were a feature measured with the MEAS or RMEAS statements. Non-indexed features (specified with FA(label2) without the [n] index option) and indexed feature point data (specified with FA(label2)[n] or FA(label2)[n,m]) cannot be mixed in a single CONST/F(label),BF statement.
The CONST ( input format 1 ) statement is passed to the output file when executed.
标签：AC,5.3,GOTO,两圆,CART,10.0000,FA,0.0000,2.0000 来源： https://blog.51cto.com/u_14941238/2903556
本站声明： 1. iCode9 技术分享网（下文简称本站）提供的所有内容，仅供技术学习、探讨和分享； 2. 关于本站的所有留言、评论、转载及引用，纯属内容发起人的个人观点，与本站观点和立场无关； 3. 关于本站的所有言论和文字，纯属内容发起人的个人观点，与本站观点和立场无关； 4. 本站文章均是网友提供，不完全保证技术分享内容的完整性、准确性、时效性、风险性和版权归属；如您发现该文章侵犯了您的权益，可联系我们第一时间进行删除； 5. 本站为非盈利性的个人网站，所有内容不会用来进行牟利，也不会利用任何形式的广告来间接获益，纯粹是为了广大技术爱好者提供技术内容和技术思想的分享性交流网站。